Saturday 13 December 2008

An introduction to low power FM transmission (or pirate radio basics...) part 1


Important notice: this information is for educational purpose only.

We hope to make you conversant with the main principles and methods of fm propagation.
If you intend to "break-in" the fm band, don't read any further!

Beginner's guide to low power broadcasting:

"Before you commit to your first broadcast - it would be advisable to have an attorney
available, who is sympathetic to the cause."

"...It's fairly easy for the DTI to track a transmission back to its source, by triangulating the signal."

"In court dress neatly and be polite to the bastard (magistrate) and the filth"
Before we go any further please have a look at: http://www.c6.org/archive/radio/pirate-fm.htm

In the next articles, we'll have a closer look at:

- What equipment do I need (part2)?

- What frequency should I choose(part3)?

- How far will my signal go (part4)?

- Considerations on dynamics (part 5).

Hope it will be of some inspiration for those interested in FM propagation.

Happy reading!

An introduction to low power FM transmission (or pirate radio basics...) part 3

What frequency should i choose?

Choose a frequency nobody is else is using, simple as that!

Most importantly!

Make sure you dont interfere with other (especially officially valid) radio users

Before you transmit, (days before even!) roam the area you will cover with a good radio, make sure nobody is using your desired frequency.
Find a quiet part of the spectrum, make sure your signal does not break-in(bleed) onto an adjacent used frequency.
Find out how your rig behaves at full power (cold, warm and hot) in an isolated area, is there frequency any drift?
Get an SWR meter (and use it!) http://www.smeter.net/feeding/swrmeter.php

Finally, read all you can about the subject. And note regional differences such as pre-emphasis

http://www.freeradio.org

Radio terms and abbreviations http://www.dxing.com/radioterms.htm
ARRL abreviations http://www2.arrl.org/qst/aguide/Abbrev_AWE.pdf

If your not creating a nuisance - then you may just get away with it!

Happy raving :)

An introduction to low power FM transmission (or pirate radio basics...) part 2

What equipment do I need?

The portable set up:

This is a quick review on what you need. Make sure to browse the internet for further detailed information.

Tape player

We advice you to go for a reliable professional cassette player
with a good rca or xlr output.

like the Sony tcd5 pro2

A Sony Pressman may do the trick as well.

"Townies iPod and MP3 players won't give you any satisfaction!"

Preamp


Assume every portable transmitter you can find is not intended to compete with professional broadcasters, a preamplifier will be handy to strengthen your signal. We are using a Nagra IV.2 for this. The main inconvenient is its weight. Walking in fields to the broadcasting location or climbing up stairs with the bastard on your back will make you consider getting its hard to find but well efficient pocket-sized little sister: the Nagra SN.

the Nagra SN:

You may also skip the Nagras and go for a home made portable console.

Here is a starting point then:
These people know the ropes on Telefunken, Siemens, EMT, Neve equipment.

http://www.danalexanderaudio.com/
http://www.marquetteaudiolabs.com/

Transmitter

This is the core of your system. May we suggest you to make a search on the interweb for "portable fm transmitter"?

We don't want to put you on the screw too much ladies but don't make us plough the sands. Does it mean anything??? ... Hahaha (from a book of English idioms)

Look for something you like with similar specifications to a Bext P10.

Bandpass filter

This is all about harmonics (multiples of your tranmissions frequency).

Let's say you're broadcasting on nine-o-nine Mhz, your aerial will send harmonics of this frequency as well. In that case 181.8, 363.6, 727.2, etc… Mhz, which are not inside the 87-108 fm band anymore.

You'll be a pain in the neck for emergency services (police, ambulances, firemen) without even noticing it… which means they'll put the DTI on your case without any delay. You may loose half a dB using it, although the loss of that dB might save somebodies life!
or help somebody get away :)

Power supply

Your power requirements will depend on your rig. 12v is the normal requirement, so a car battery is suitable (without the car running! or use a regulation circuit). Car emergancy starters are good (dont be tempted by the crap strobes on it though). Deep discharge battery will last longer and give better performance, electric wheelchairs use these, so they are easy pickings!:)

The more you spend, the more power you get, also it's easier to carry.
cheaper > more expensive: lead acid, Gel Lead acid, NiCads, Lithium Based batteries.
The more efficient (and expensive) the battery technology is, can also mean it's more difficult (expensive) to charge safely.

If you are going to be located in one place for some time, you may be able to use the forces of nature to keep you powered up i.e., solar or wind can trickle charge your batteries in time for your broadcasts.

Here's some links:

http://electronics.howstuffworks.com/battery.htm
http://www.vonwentzel.net/Battery/00.Glossary/
http://www.batteryweb.com/
http://www.exideworld.com/
http://www.mdsbattery.co.uk/defaultuk.asp
http://www.homepower.com/
http://www.americansolarchallenge.org/event/asc2005/
http://www.rain.org/~philfear/how2solar.html
http://home.earthlink.net/~fradella/green.htm

Mast

Unless you can find a location atop of a high building, a mast is a must!
Go for an air-operated 10 to 12 meters high mast which is the best value for weight, strenghtness and minimum retracted height.

http://www.alphalink.com.au/~gfs/Clark/clarkp30.htm

You can also go DIY with aluminum tubes and guy wires.

Antenna

The other key part of your radio station. It is similar to a loud speaker in a stereo system.
Again, we advice you to have a deep look on the internet on different models and manufacturers.
http://www.ac6v.com/antprojects.htm

Cable

It brings the signal from your transmitter to the aerial. Keep it as short as possible.
Any unnecessary meter will weaken your signal and then the signal/noise ratio.
To get it, have a quick look at some electricity basics here.
http://hyperphysics.phy-astr.gsu.edu/hbase/electric/ohmlaw.html

Quality RG213 cable is a good choice.

Other

Don't go out for a broadcast without appropriate clothing! It's too late to think about your missing top when you're on air. Double check batteries and that you take any tools you need for mast erection, rope, gloves and flashlight. A sweety may be welcome and a glass of Merlot as well! You may be in a rude environment; it doesn't mean you have to get rid of pleasures of life.

Friday 12 December 2008

Everything you ever wanted to know

about the history of electronic instruments, at this beautiful page.

A belgian semi-automatic pressing machine!!!


How wicked does that look? Fabel means "Fabrique Belge", its other name is "FN", stands for "Fabrique Nationale". They stopped producing that machine a long time ago, but they still make weapons for the belgian army, and that's not so cool...


More on record cutting

On Flo Kaufmann's page, lots of lathes, cutterheads, amplifiers, and pressing machines.

Some record cutting lathes...

The Neumann R20, the very first one, built circa 1932, designed to cut on wax plates... What did they do with the cut afterwards? This one belongs to the Deutsches Rundfunk Museum.






The AM131, the first cutting lathe mass produced by Neumann, that one's got a fixed pitch. Notice how similar it is to the R20, even their last model the VMS82, kept the same shape.






Gotham Audio designed a 3 speeds motor for it:






A Fairchild lathe, note the carriage arm, same as on the Lyrec lathe, quoted by Mr Sean Davies as "very reliable, much more stable, brilliant idea..."







The Lyrec lathe, from Denmark:






A Scully lathe, this one actually belongs to us, but is not functional, yet:






The Neumann VMS 66, was the first cutting with an electronic pitch. It had 4 points of reference, it's accurate, but better could be achieved.






Then came the ultra-famous Neumann VMS 70, basically identical to the VMS 60, but the pitch control and some electronics were improved. As well as the aesthetics...






The Daddy, the Neumann VMS80, you can't do better than this:







Well you actually can... The Neumann VMS82, the very last ever designed, built to cut on copper. Only 34 were made... It's basically a VMS80, modified to make it much more stronger.






Drive Time Advert / FSK014/WEME017 / Ceephax Acid Crew